Ultraguard PRO 9549UG Manuel d'utilisateur télécharger pdf

Page 1

Model PRO 9549UG

Installation Manual

SELECTABLE FEATURES

Note : The method of manual override can either be selected to operate from the valet switch or operate as custom code. Be

certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.

Dip Switch Selectable Features :

Switch Number ON Position OFF Position Factory Default

Dip Switch 1 Custom Code Override Valet Switch Override Valet Switch Override

Dip Switch 2 Voltage Sense Hardwire Voltage Sense

Note : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s door pin switch in order to

begin the passive arming sequence.

RF Programmable Features :

Feature Selection 1 Chirp 2 Chirps Default

First 1 Second Door Locks 3.5 Second Door Locks 1 Second

Second Auto Lock On Auto Lock Off Auto Lock Off

Third Auto Unlock On Auto Unlock Off Auto Unlock Off

Fourth Headlight Output On Headlight Output Off Headlight On

Fifth Passive Door Locks Active Door Locks Passive Locks

Sixth Passive Arming Active Arming Active Arming

To program these selectable features;

Action System Response

Turn ignition on No response

Flip valet switch on then off 3 times 1 Chirp - LED 1 flash

Within 3 seconds, turn ignition Off Short chirp, then long chirp

First Then On 1 chirp = 1 second door locks

Press the Lock/Unlock button to change 2 chirps = 3.5 second door locks

Second Flip valet switch on then off 2 chirps = auto locks off

Press the Lock/Unlock button to change 1 chirp = auto locks on

Third Flip valet switch on then off 2 chirps = auto unlock off

Press the Lock/Unlock button to change 1 chirp = auto unlock on

Fourth Flip valet switch on then off 1 chirp = headlight output on

Press the Lock/Unlock button to change 2 chirps = headlight output off

Fifth Flip valet switch on then off 1 chirp = passive locks

Press the Lock/Unlock button to change 2 chirps = active locks

Sixth Flip valet switch on then off 1 chirp = passive arming

Press the Lock/Unlock button to change 2 chirps = active arming

Flip valet switch on then off Exit program mode

Turn ignition key off Exit program mode

Note : Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps, or the

programming will be terminated.

1 2 3 4 5 6 7 8

Model PRO 9549UG 1
CONTROL MODULE 7

Résumé du contenu

Page 1 - Model PRO 9549UG

Page 1Model PRO 9549UGInstallation ManualSELECTABLE FEATURESNote : The method of manual override can either be selected to operate from the valet swit

Page 2

Page 2INSTALLATION OF MAJOR COMPONENTSControl Module :Select a mounitng location inside the passenger compartment ( up behind the dash ), and secure u

Page 3

Page 3When installing this system into vehicles with electronic “ after fans “, it is recommended you disable the voltagesense circuit.In voltage sens

Page 4

Page 4Mini 10 Pin Edge Connector :Light Green Wire : ( - ) Instant Trigger Zone 1This is an instant on ground trigger wire. This wire ( zone ) should

Page 5

Page 5This wire provides an immediate ground signal, and stays at ground for up to 8 seconds as long as the button(s) onthe keychain transmitter remai

Page 6

5 Wire Alternating Door Lock Circuits :In this application, it is necessary to cut the existing door lock by - pass wires. These wires run from the ma

Page 7 - CONTROL MODULE

Page 7RED87A858630CUTTOIGNITIONSWITCHTOSTARTSOLENOID87TO +12 VDCIGN./CRANKEXISTING LOW CURRENT SOLENOIDFEED WIRE (+12VDC, CRANKING ONLY)PRO 9549UGCO

Page 8

PRO 9549UGCONTROL MODULEBLACK2 STEP UNLOCKRELAY OUTPUTSTo Relay Terminal #85To Relay Terminal #86LT. BLUEL.E.D.ZONE 1Optional Negative TriggeringAlar

Commentaires sur ces manuels

Pas de commentaire

Ultraguard PRO 9549UG Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Sécurité Ultraguard PRO 9549UG. UltraGuard PRO 9549UG User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels